| Customization: | Available |
|---|---|
| Material: | Aluminium |
| Usage: | Heavy Duty Clamp, Pipe Clamp, Glass Clamp |
|
Still deciding? Get samples of US$ 1/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Suspension Clamps are used as a component of insulator string which we can use it to hang conductor or ground wire to the tower arms or substation structures with insulators and line fittings.
Power fittings suspension clamps are divided into old-fashioned boat-shaped clamps and pre-twisted suspension clamps.
Pre-twisted suspension clamps:
Pre-twisted suspension clamp functions and uses: used for connecting ADSS optical cables, OPGW optical cables, various conductors, etc. in linear pole towers. The single-sided suspension angle is 15°-18°. The combination of inner and outer spiral pre-twisted wires can be very A well-protected optical cable has no concentrated stress, avoids bending stress, and plays a role in protecting the optical cable and auxiliary vibration reduction. The complete set of suspension clamps includes: inner and outer pre-twisted wires, suspension heads and supporting connecting hardware. The clamp's holding force is 10%-20% greater than the rated tensile strength of the optical cable, making installation easy.
Pre-twisted suspension clamps are divided into Suspension clamp for OPGW and Suspension clamp for ADSS:
This Helical suspension clamp is used for connection between ADSS cable and straight support with corner/elevation angle
within25° -60° . Each tower has one set.
Structure and Material for each part:
| Item | Material |
| Suspension Clamp | Aluminum alloy |
| Helical armor rod wire | Aluminum alloy |
| Aluminum Clamping Plate | Breaking load 80kN |
| U-type Holder | Aluminum alloy |
| Rubber Pad | Synthetic rubber |
| PS-type Plate | Hot-DIP galvanized steel, GB fitting |
| Yoke Plate | Hot DIP galvanized steel, GB fitting |
| Z-type Plate | Hot DIP galvanized steel, GB fitting |
Product Features:
a. The suspension clamp has a large contact area with the ADSS optical cable, the stress is distributed evenly, and there are no stress concentration points. At the same time, it increases the stiffness of the hanging point optical cable and plays a better protective role.
b. It has good dynamic stress tolerance and can provide sufficient gripping force to protect the ADSS optical cable when operating under unbalanced load conditions.
c. The structure is equipped with soft rubber clamps to achieve self-damping and reduce wear.
d. Use aluminum alloy protective strips to protect optical cables.
e. The ends are rounded to increase the corona initiation voltage.
f. The aluminum alloy material improves the mechanical performance and anti-corrosion performance of the cable clamp, greatly extending the service life.
Product specification parameter:
Product Use:
This kind of pre-twisted suspension clamp is a connecting fitting for suspending OPGW optical cables on transmission line towers. The cable clamp can reduce the static stress of the optical cable at the suspension point, improve the vibration resistance of the optical cable, and suppress the dynamic stress of wind vibration; it can also ensure that the bending of the optical cable does not exceed the allowable value, so that the optical cable does not produce bending stress. Since the cable clamp is installed on the optical cable, no harmful stress concentration will occur, so the optical fiber in the optical cable will not produce additional losses.
Product Structure and materials:
This product is a combination wire clamp, equipped with a hanging head (each hanging head is composed of a rubber clamp, an aluminum splint, a bolt, a spring washer, a flat washer, a nut, a closing pin, etc.), an outer layer of pre-twisted wire, and a protective wire pre-twisted wire. etc. are combined.
The pre-twisted wire of the protective strip is directly wrapped around the surface of the optical cable to provide protection and stiffness for the optical cable. The pre-twisted wire of the protective strip is clamped by the rubber clamp insert, and the middle lay length of the outer pre-twisted wire presses the drum-shaped rubber clamp. , and then clamp the outside with aluminum plywood.
Aluminum plywood ------ is made of corrosion-resistant aluminum alloy pressure casting. The aluminum alloy has stable chemical properties, good atmospheric corrosion resistance, and good mechanical properties.
Rubber clamp------composed of high-quality rubber and central reinforcement, it has ozone resistance, chemical resistance, weather aging resistance, high and low temperature performance, high strength and elasticity, and small compression deformation.
Bolts, spring washers, flat washers, nuts ------ hot-dip galvanized standard parts.
Closing pin------electrical standard parts.
Protective wire pre-twisted wire------aluminum alloy wire customized according to predetermined mechanical properties and chemical composition. It has high tensile strength, hardness, good elasticity and strong anti-rust ability, and can survive in harsh climates. environment for long-term use.
The outer layer of pre-twisted wire is the same as the protective wire pre-twisted wire.
Connection hardware ------ U-shaped hanging rings, U-shaped screws, UB-shaped hanging plates, and ZH-shaped hanging rings are all standard electrical parts.
Product specification parameter:
| Catalog Number | Diameter Range(mm) | Inner rods | Outer rods | Breaking Strength(kN) | ||
| Length (mm) | Average Weight(kg) | Length (mm) | Average Weight(kg) | |||
| ONL0800 060 | 7.8-8.0 | 950 | 0.5 | 740 | 0.5 | 67 |
| ONL0880 060 | 8.0-8.8 | 950 | 0.5 | 740 | 0.5 | 67 |
| ONL 1010 080 | 8.9-10.1 | 1110 | 0.6 | 850 | 0.6 | 89 |
| ONL 1140 100 | 10.2-11.4 | 1244 | 0.7 | 902 | 0.7 | 111 |
| ONL 1280 100 | 11.5-12.8 | 1372 | 0.8 | 990 | 0.9 | 111 |
| ONL 1410 100 | 12.9-14.1 | 1474 | 1.0 | 1067 | 1.3 | 111 |
| ONL 1550 100 | 14.2-15.5 | 1600 | 1.3 | 1143 | 1.4 | 111 |
| ONL 1730 100 | 15.6-17.3 | 1728 | 1.5 | 1245 | 1.9 | 111 |
| ONL 1920 100 | 17.4-19.2 | 2160 | 2.2 | 1613 | 3.1 | 111 |
| ONL 2110 100 | 19.3-21.1 | 2312 | 2.6 | 1715 | 3.3 | 111 |
| ONL 2340 100 | 21.2-23.4 | 2490 | 3.0 | 1842 | 4.4 | 111 |
| ONL 2620 100 | 23.5-26.2 | 2718 | 3.4 | 1994 | 4.8 | 111 |
Quality Control:
HeBei LeiCheng Since its inception, always adhere to the "quality first, credit first" business purpose, constantly develop innovative products, expand the market, and with many scientific research units, colleges and universities work closely and hired professional and technical personnel as guideline, USES the domestic and foreign advanced technology, experienced several years of hard struggle, finally achieved gratifying results.
Our company has products of all specifications and its major products are overhead insulator fittings, poleline accessories, power line fittings, porcelain insulators and so on. The company has a strong technological power, top-ranking production.
The company pays attention to the development of products, research and development at the same time, constantly strengthen the quality management.
Office Environment
Factory
You can rest assured that the packaging of the product, as the last link we strictly control!
Certificate
FAQ
Q: Are you a Manufacturer, factory or Trading company ?
A: Yes, We are engaging in the research and development, production and operation of transformer for over 10 years.
Q: What's your warranty terms?
A: We offer 12 months warranty time.
Q: Production Time?
A: In general, it take 4~6weeks and it depend on the different style.
Q: What's your payment terms?
A: Pay by T/T and L/C is acceptable.
Q: How do you conduct quality control in your factory?
A: We implement 100% QC inspection to ensure every product is qualified. We have over 10 times QC inspections during the manufacturing process from raw material to the final products.Each of our unit has 3C certificate. If you need any other Certificate, we can help you to apply it.
Q: Do you have the products in stock?
A: Normally no. All our products produce depending to your order quantity.
Q: What should provide to make custom transformer ?
A: Technical drawing and technical specification document are the best, or you can tell us some details technical specification date as below "Quotation and Ordering Required Information".
Q: Could I have your catalog and price list for trial order in MOQ quantity?
A: All of our products are showing on Made-in-China or official website, you are always welcome to ask us to get more information directly.
Our plants produce all electric power fittings, including Cross Arm, Stay wire, Clamp, U bolt, Guy Clip, Thimble Clevis, PD Clevis and more. Related products can be found on our home page, or contact me directly, let me help you!
Welcome to our homepage to see more content!
){kind=link}